Mower #3 - Wright Stander X
Wright Stander X
- Type
- Stander 52
- Hours
- 1693.4
- Miles
- —
- VIN / Serial
- 140272PC
- Plate
- —
- Tag Exp.
- —
- Insurance Exp.
- —
- Inspection Status
- —
- Inspection Expiration
- —
- Purchase Date
- —
- Warranty Expiration
- —
- Separate Engine Warranty
- No
- Notes
- —
Report a Problem
Repair History
| Ticket | Type | Status | Start Work | Pickup | Problem / Service | Diagnosis | Parts | Parts Price | Labor | Assigned | Submitted By | Location | Notes |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| #120 | Repair | Waiting for Parts | 10/13/2026 | — | Both hydro pumps leaking | Both hydro pumps are leaking. Upper gaskets leaking on both left and right pumps. Seal kits have been delivered. Caster wheel on front right is broken. Inspection of unit shows no other issues at this time. | Seal kits and fluid | — | — | Unassigned | Brad | — | parts have been delivered, ordered new check valve and spring |
| #38 | Repair | Waiting for Parts | 9/3/2026 | — | Both hydro pumps leaking | Both hydro pumps are leaking. Upper gaskets leaking on both left and right pumps. Seal kits have been delivered. Caster wheel on front right is broken. Inspection of unit shows no other issues at this time. | Seal kits and fluid | — | — | Unassigned | Brad | — | parts have been delivered, ordered new check valve and spring |
| #30 | Repair | Completed | 8/12/2026 | — | No Start, clicking when attempting to start but no engagement or movement during attempt | Starter not engaging, tested battery for proper voltage, tested good at 12.6 volts, installed new starter to confirm operation no change in behvaior, motor is not spinning at all. Used power probe to check for 12V signal to start from key, power goes from key switch to PTO switch does NOT go from PTO switch to starter, issue is in harness, Need new Harness. | New starter, swapped ignition key | — | 4 | Brad | Merritt | Shop | Power drop from battery to pto, denying starter of power to engage, replaced starter to confirm, replaced ignition key to test for power, checked oil level slightly low, confirmed voltage drop at battery due to rusted frayed wire, cut power wire back cleaned up connection, added new eylet connector, tested function, unit now starts and engages without issue. |
| #18 | Repair | Completed | 8/8/2026 | — | Clicking but wont turn over | Fuel shut off relay over heating, harness having connection breaks during start up function, ignition key losing connection. | Replace ignition key assembly, fuel safety shut off harness and relay | — | 2 | Brad | Merritt | — | made repairs, crew has mower back on truck |
Complete Equipment Timeline
Repairs, service, equipment changes, and renewal dates in one history.
Both hydro pumps leaking
Unassigned · Both hydro pumps are leaking. Upper gaskets leaking on both left and right pumps. Seal kits have been delivered. Caster wheel on front right is broken. Inspection of unit shows no other issues at this time. · parts have been delivered, ordered new check valve and spring
Waiting for PartsUpdated
Updated repair: Both hydro pumps leaking.
Updated
Updated repair: Both hydro pumps leaking.
Updated
Updated repair: Both hydro pumps leaking.
Updated
Updated repair: Both hydro pumps leaking.
Both hydro pumps leaking
Unassigned · Both hydro pumps are leaking. Upper gaskets leaking on both left and right pumps. Seal kits have been delivered. Caster wheel on front right is broken. Inspection of unit shows no other issues at this time. · parts have been delivered, ordered new check valve and spring
Waiting for PartsUpdated
Updated repair: Both hydro pumps leaking.
Updated
Updated repair: Both hydro pumps leaking.
Updated
Updated repair: Both hydro pumps leaking.
Ticket submitted
Ticket submitted by Brad: Both hydro pumps leaking
Completed
Updated repair: No Start, clicking when attempting to start but no engagement or movement during attempt.
No Start, clicking when attempting to start but no engagement or movement during attempt
Shop · Brad · Starter not engaging, tested battery for proper voltage, tested good at 12.6 volts, installed new starter to confirm operation no change in behvaior, motor is not spinning at all. Used power probe to check for 12V signal to start from key, power goes from key switch to PTO switch does NOT go from PTO switch to starter, issue is in harness, Need new Harness. · Power drop from battery to pto, denying starter of power to engage, replaced starter to confirm, replaced ignition key to test for power, checked oil level slightly low, confirmed voltage drop at battery due to rusted frayed wire, cut power wire back cleaned up connection, added new eylet connector, tested function, unit now starts and engages without issue.
CompletedEquipment information updated
Hours, mileage, identification, status, or notes were updated.
OperableDay-of email sent
Day-of email sent for Mower #3 - Wright Stander X.
Updated
Updated repair: No Start, clicking when attempting to start but no engagement or movement during attempt.
Day-of email sent
Day-of email sent for Mower #3 - Wright Stander X.
Updated
Updated repair: No Start, clicking when attempting to start but no engagement or movement during attempt.
Day-of email sent
Day-of email sent for Mower #3 - Wright Stander X.
Ticket submitted
Ticket submitted by Merritt: No Start, clicking when attempting to start but no engagement or movement during attempt
Completed
Updated repair: Clicking but wont turn over.
Clicking but wont turn over
Brad · Fuel shut off relay over heating, harness having connection breaks during start up function, ignition key losing connection. · made repairs, crew has mower back on truck
CompletedUpdated
Updated repair: Clicking but wont turn over.
Equipment record created
Mower #3 - Wright Stander X
Ticket submitted
Ticket submitted by Merritt: Clicking but wont turn over